Oil play · Williston Basin
Bakken and Three Forks play
The horizontal-well oil play of the Williston Basin: the thin middle Bakken and the upper Three Forks, charged by two black Bakken shales.
U.S. part of the Williston Basin, North Dakota and Montana.
Play record
- Location
- North Dakota and Montana
- Wells
- More than 17,500 (2021)
U.S. Geological Survey Fact Sheet 2021-3058[1]
Oil produced
About 4 billion barrels by 2021[1]
Undiscovered oil (USGS 2021 mean)
4.3 billion barrels, plus 4.9 trillion cubic feet of gas[1]
USGS 2013 estimate
7.38 billion barrels: 3.65 Bakken and 3.73 Three Forks[2]
The story
- Oil is produced by horizontal drilling and hydraulic fracturing of the middle Bakken and upper Three Forks; the lower Three Forks and the other Bakken members are still being tested.[2]
- The USGS assessed the Bakken in 2008 and 2013 and the Three Forks first in 2013. Between 2013 and 2021 more than 6,400 more Bakken wells and about 4,100 Three Forks wells were drilled.[1]
What a well drills through
The main rock layers above and in the reservoir, top down. Tap a layer for a summary.
- Limestone and marl
- Dolomite
- Salt and evaporites
- Mudstone and shale
- Organic-rich mudstone (source rock)
- Sandstone
The trap
A continuous accumulation: oil from the upper and lower Bakken shales moved only a short way, into the middle member, the Pronghorn and dolomitized Three Forks. The upper shale marks its outer limit.[1]
Reservoir rocks
- Bakken Formation
A thin Late Devonian to Early Mississippian sandwich: two black, organic-rich shales around a silty dolomite and sandstone middle member. The shales made the oil; horizontal wells in the middle member produce it.
- Three Forks Formation
Late Devonian dolomite, siltstone and dolomitic shale under the Bakken, charged by the Bakken lower shale. Its upper part is the second big horizontal target of the play.
Where wells do best
What to watch for
- Salt at 5,000 to 12,500 ft has collapsed casing across the basin: flowing salt loads casing where washed-out hole was poorly cemented. Keeping drilling-fluid flow laminar limits the washout.[3]
GeoEngine Field Intelligence
This page, inside your geosteering project
Field Intelligence in GeoEngine writes a cited report on the field your well is in: the formations, how they read on logs, where wells do best and what can go wrong. Next, those reports will start from the Atlas entry for your field.
See Field IntelligenceSources
Written in our own words from these sources. Checked 17 November 2026.
- 1Marra and others (2021), Assessment of undiscovered continuous oil resources in the Bakken and Three Forks Formations of the Williston Basin Province, North Dakota and Montana, 2021. U.S. Geological Survey Fact Sheet 2021-3058.
- 2Gaswirth and Marra (2015), U.S. Geological Survey 2013 assessment of undiscovered resources in the Bakken and Three Forks Formations of the U.S. Williston Basin Province. AAPG Bulletin 99 (4), 639 to 660.
- 3Stash and Jones (1988), Williston Basin: an analysis of salt drilling techniques for brine-based drilling fluid systems. SPE Drilling Engineering 3 (1), 19 to 32.
- 4FGDC Digital Cartographic Standard for Geologic Map Symbolization (FGDC-STD-013-2006), section 37: lithologic patterns. U.S. Geological Survey Techniques and Methods 11-A2.