Oil field · Norwegian Viking Graben and Utsira High

Gullfaks field

A heavily faulted Tampen field producing from Jurassic and Triassic sands, and from fractured Shetland Group and Lista rock above them.

Block 34/10, Tampen area, northern Norwegian North Sea.

Field record

Discovered
1978
Discovery well
34/10-1
First production
1986
Water depth
130 to 220 m
Operator
Equinor

Norwegian Offshore Directorate FactPages[1]

Recoverable oil

391 million Sm³[2]

Recovery factor (2008)

56% overall, 60% in the Brent[3]

Reservoir depth

1,700 to 2,000 m[2]

The story

  • Discovered in 1978 and producing from 1986 from three concrete platforms, Gullfaks A, B and C, which also handle oil from several neighbouring fields.[2]

What a well drills through

The main rock layers above and in the reservoir, top down. Tap a layer for a summary.

  • Mudstone and shale
  • Limestone and marl
  • Sandstone
  • Coal
Layers shown in order, not to scale. The reservoir is highlighted. Rock patterns follow the USGS FGDC lithology standard.

The trap

Rotated fault blocks in the west and a horst in the east, with a highly faulted zone between. Many faults are below seismic resolution, and some reverse faults cut the mostly normal-faulted field.[2, 4]

Reservoir rocks

  • Brent Group

    The Middle Jurassic delta sands that made the northern North Sea: the reservoir of Brent, Ninian, Thistle, Dunlin and Alwyn North.

  • Cook Formation

    Early Jurassic marine sand inside the Dunlin mudstones. A reservoir at Statfjord, Gullfaks and the Oseberg satellites, but with low permeability at Gullfaks.

  • Statfjord Formation

    Latest Triassic to Early Jurassic sandstones laid down by rivers and fan deltas. The deeper of the two reservoirs at Brent and Alwyn North.

  • Hegre Group

    Triassic red beds of the northern North Sea, over 2 km thick in the east. Its Lunde river sands are the reservoir at Snorre and part of Gullfaks.

Where wells do best

  • Tarbert and Statfjord sands are highly productive; Tarbert permeability reaches several darcies. Reservoir quality within each fault compartment is good to very good.[2, 3, 4]
  • Highly deviated and horizontal wells combine several reservoirs in one well.[4]

What to watch for

  • Overpressure in the Shetland/Lista interval made drilling difficult for years; production from it has gradually lowered the pressure.[2]
  • Poorly consolidated sands produce sand after water breakthrough; some areas have high hydrogen sulphide (H2S).[3, 4]
  • Poor communication between fault compartments makes pressure support hard.[2]

GeoEngine Field Intelligence

This page, inside your geosteering project

Field Intelligence in GeoEngine writes a cited report on the field your well is in: the formations, how they read on logs, where wells do best and what can go wrong. Next, those reports will start from the Atlas entry for your field.

See Field Intelligence

Sources

Written in our own words from these sources. Checked 17 November 2026.

  1. 1Fields: discovery wellbore, operator and status. Norwegian Offshore Directorate FactPages (open data).
  2. 2Gullfaks: field description (development, reservoir, recovery strategy, status) and recoverable reserves at 31 December 2025. Norwegian Offshore Directorate FactPages.
  3. 3Talukdar and Instefjord (2008), Reservoir management of the Gullfaks Main Field. SPE 113260, Europec/EAGE Conference.
  4. 4Tollefsen, Graue and Svinddal (1992), The Gullfaks Field development: challenges and perspectives. SPE 25054, European Petroleum Conference.
  5. 5FGDC Digital Cartographic Standard for Geologic Map Symbolization (FGDC-STD-013-2006), section 37: lithologic patterns. U.S. Geological Survey Techniques and Methods 11-A2.