Formation · Jurassic

Cook Formation

Early Jurassic marine sand inside the Dunlin mudstones. A reservoir at Statfjord, Gullfaks and the Oseberg satellites, but with low permeability at Gullfaks.

  • Reservoir

Overview

AgePliensbachian to Toarcian, 192.9 to 174.7 million years ago[1, 2]
RankFormation, part of the Dunlin Group[2]
Other namesGiven sub-unit status by Deegan and Scull (1977) and later raised to a formation.[2]
Type sectionUK well 211/29-3, 2,887 to 2,950.5 m. Reference sections in Norwegian wells 33/9-1, 30/6-7, 31/2-1 and 30/7-7.[2]
Thickness41 to 86 m in the wells described.[2]
WhereEast Shetland Basin and the northern Horda Platform.[2]

Entry coverage

13 of 20 topics

Not yet sourced

Sequence stratigraphic setting, Fossils and dating, Diagenesis, Reservoir quality, Source rock potential, Seal quality, Uncertainties. These are added only when a public source supports them. How the Atlas is made

Rocks and composition

Lithology

Reported

Marine siltstone with claystone at the type well; on the Horda Platform mostly white to greyish-brown, very fine to fine, well sorted sandstone.[2]

Mineralogy

Reported

Silica is the most common cement; mica, glauconite, carbonaceous matter and calcite cement occur.[2]

Grain size, sorting and structures

Reported

Sandstone grains are subangular to subrounded and well sorted, with occasional thin medium to coarse beds; the sandstones are hard to friable. In the siltstones and claystones, sandy streaks become more common away from the type well.[2]

How it was laid down

Depositional environment

Published interpretation
  • Muddy sea shelf. The sea floor of a shallow continental shelf, below the reach of everyday waves. Silt and mud settle, and animals burrow through them.[2]
  • Shoreface and shallow sea. The zone from the beach out to where waves stop stirring the bottom. Waves sort the sand well, and burrowing animals mix it.[2]

Facies

Published interpretation

Three sandstone types: marine shoal sands around Statfjord, prograding shelf sands in several cycles on the Horda Platform, and thinner sands redeposited from the shelf edge in the graben.[2]

Boundaries and logs

Boundaries

Reported

Picked by a fall in gamma ray and a rise in velocity against the more uniform, more argillaceous rocks above and below.[2]

Log response

Reported

Lower gamma ray and higher velocity than the more clay-rich rock above and below.[2]

Petroleum significance

  • Reservoir

Members and notes

Worth knowing

Published interpretation

At Statfjord the sands are marine shoals; on the Horda Platform they are shelf sands building out in several cycles.[2]

Worth knowing

Published interpretation

Permeability at Gullfaks ranges from several darcies in the Tarbert to millidarcies in the Cook.[3]

Fields that drill it

Neighbours in the column

Where it sits in geological time.

Neighbours follow the Atlas column. Members sit inside their parent unit, and some units are missing in parts of a basin.

GeoEngine Field Intelligence

This page, inside your geosteering project

Field Intelligence in GeoEngine writes a cited report on the field your well is in: the formations, how they read on logs, where wells do best and what can go wrong. Next, those reports will start from the Atlas entry for your field.

See Field Intelligence

Sources

Written in our own words from these sources. Checked 17 November 2026.

  1. 1International Chronostratigraphic Chart, version 2024/12. International Commission on Stratigraphy.
  2. 2Cook Formation, NW European Stratigraphic Lexica (after NPD Bulletin 3, Vollset and Doré 1984). Norwegian Offshore Directorate and the Timescale Foundation.
  3. 3Talukdar and Instefjord (2008), Reservoir management of the Gullfaks Main Field. SPE 113260, Europec/EAGE Conference.
  4. 4Statfjord: field description (development, reservoir, recovery strategy, status) and recoverable reserves at 31 December 2025. Norwegian Offshore Directorate FactPages.