Careers in geosteering

Geosteering interview questions

The questions geosteering interviews tend to ask, grouped by topic, each with what a strong answer covers. Use them to prepare, or to run an interview.

Updated 17 November 2026 · GeoMaster technical team

How to prepare

  • Revise the basics until they are automatic: how geosteering works, apparent dip, MD and TVD, dogleg.
  • Bring two or three wells you steered: what the plan was, what you saw, the calls you made, and how much of the lateral stayed in zone.
  • Practise correlating a horizontal well against a type well out loud. Explaining your reasoning is half the test.
  • Know the vocabulary of the role; the geosteering glossary covers it.
  • Read up on the employer's basins and the software in the advert.

Logs and correlation

Why does a marker look thicker in the lateral than in the type well?

What a good answer covers: Because the well crosses the layer at a low angle, so it spends more measured depth in it. The apparent thickness grows roughly with 1 / sin of the angle between the well and the bedding. A strong answer adds that you correlate in true vertical thickness (or stratigraphic) space, not measured depth.

How do you choose a type well?

What a good answer covers: Closest offset with good log quality, the same stratigraphy and similar thickness, ideally along the planned well direction. Check its tops against neighbours and its survey. Mention what you do when no offset is good: build a composite, or log the landing and use that.

The gamma ray stops matching anything. What do you do?

What a good answer covers: Do not steer hard on it. Check the data first (depth shift, tool change, bad survey, sensor offset), then consider a fault, a facies change, or that you have crossed the boundary. Hold where safe, collect another survey, and say clearly what you think and how confident you are.

Which logs besides gamma ray help in geosteering?

What a good answer covers: Resistivity (including deep directional resistivity to see boundaries before reaching them), azimuthal gamma and image logs for up or down crossings, density and neutron where run, plus cuttings, gas and drilling data. A good answer says what each one adds, not just names it.

Dip, faults and structure

What is apparent dip, and why does it matter here?

What a good answer covers: The dip measured along the well direction. It equals true dip only when you drill straight up or down dip. Steering uses apparent dip along the vertical section, so a candidate should be able to explain why a 4° true dip can look like 2° on the section.

How do you recognise a fault in a horizontal well?

What a good answer covers: A sudden jump or repeat in the log that no dip change explains, often with a change in drilling behaviour or cuttings. A strong answer estimates the throw by re-correlating after the break and says how the steering plan changes.

You are 1.5 m below the top of a 3 m target and the dip is steepening down. What do you recommend?

What a good answer covers: Look for a short, testable call: drop inclination enough to stay parallel and drift towards the centre, state the expected position at the next survey, and the trigger for revising. Interviewers care more about the reasoning and the check than the exact number.

Surveys and drilling

What is dogleg severity and why does the driller care?

What a good answer covers: The total change in wellbore angle between surveys, normalised per 30 m or 100 ft. High dogleg makes casing and completion harder and increases torque and drag. A good answer links it to steering: every correction costs dogleg, so calls should be smooth and early. Practise with the dogleg severity calculator.

What is the difference between MD, TVD and vertical section?

What a good answer covers: Measured depth is along the hole, TVD is straight down, vertical section is horizontal distance along a chosen azimuth. Cross-sections plot TVD against vertical section. Practise with the md to tvd converter.

Why does sensor-to-bit distance matter?

What a good answer covers: The log describes rock the bit drilled some metres ago. You steer for where the bit is, so you project ahead of the last survey and the sensor. Expect a follow-up on how build rate limits how fast a correction takes effect.

How do motors and rotary steerable systems change your calls?

What a good answer covers: With a motor, direction changes by sliding, which is slower and rougher, so calls are timed to keep slides short. A rotary steerable allows smaller, more frequent corrections. The geology is the same; the tool decides how finely you can steer.

Landing the curve

How do you update the landing point while building the curve?

What a good answer covers: Pick each marker above the target as it arrives, compare its depth with the prognosis, and move the predicted target depth accordingly. Tell the driller early so the build rate can change while there is still room.

What are the risks of landing too high or too low?

What a good answer covers: Too high risks drilling a long stretch in the cap rock or shale above; too low or too steep wastes lateral and may need a correction that costs dogleg. A strong answer weighs both against the reservoir and the completion.

Communication and judgement

Walk me through a steering call you made that turned out wrong.

What a good answer covers: Interviewers want honesty, what the data showed at the time, what you missed, how quickly you corrected, and what you changed in your process. Avoid answers where nothing was your fault.

The directional driller disagrees with your call. What do you do?

What a good answer covers: Listen first: they know what the assembly can do. Explain the interpretation behind the call, agree what you will check at the next survey, and escalate to the operations geologist if the risk is real. The well matters more than who is right.

How do you hand over a well at the end of a shift?

What a good answer covers: Position, current interpretation and confidence, the last calls and why, what is expected next (markers, faults), and any open questions. Written as well as spoken.

How would you cover several wells at once remotely?

What a good answer covers: Prioritise by risk (landing and faulted sections first), use alerts on new surveys, keep a short status per well, and ask for help early. Mention data links: if the feed drops, you need a fallback with the rig.

For what the job involves day to day, see the geosteering geologist; for pay, see geosteering salary; and to learn the method from the start, join the free geosteering course waitlist.

Frequently asked questions

What do geosteering interviews usually test?+

Log interpretation and correlation, structural reasoning (dip, faults), survey basics, and how you communicate a decision under pressure. Many include a practical exercise: correlating a lateral against a type well, or explaining a cross-section.

Will I be asked to correlate a well in the interview?+

Often, for experienced roles. You may get printed logs or a screen share in the company's software. Practise beforehand on real data; you can correlate wells in GeoMaster on the free plan.

Do I need to know a specific geosteering software?+

Adverts often name one, but interviewers mostly test the method. Say which packages you have used and show you can learn another quickly.

Steer your next well in the browser

GeoMaster® puts log correlation, the geological model and plan tracking in one browser tab. Start on the free plan, or ask for a 14-day Pro trial: we approve requests within 1 working day.