What landing means
A horizontal well drills down vertically, turns at the kick-off point, and builds angle through the curve until it is roughly horizontal. Landing the curve means finishing that build so the well enters the target layer at the planned depth, at the inclination that keeps it parallel to the layer. The point where this happens is the landing point; the lateral is drilled from there.
Why it is hard
- The target depth is a prediction. It comes from seismic and offset wells, and is often a few metres out at the well location. In a target a few metres thick, that is the whole layer.
- Angle takes distance to change. At a build rate of 3° per 30 m, the last 10° of the curve takes about 100 m of hole. Decisions made late cannot be executed in time.
- The logs lag the bit. Sensors sit metres behind the bit, so a marker is seen after the bit has passed it.
- Mistakes are expensive. Landing too high or too low wastes lateral, and fixing it costs dogleg or a sidetrack.
Before the well
- Choose the type well and confirm its tops. See our type well correlation guide.
- List the markers above the target that should be recognisable while building: their prognosed TVD and their thickness to the target top.
- Agree the landing window with the subsurface team: how far into the target to land (for example 1 m below the top), and the acceptable range.
- Agree the build plan with the directional driller: planned build rate, the maximum the assembly can deliver, and where a tangent could go.
- Set decision points: at which markers you will review the landing, and who signs off a change.
Updating the landing marker by marker
As each marker arrives, compare its true vertical depth with the prognosis. If the layers keep their thickness between the marker and the target, the target moves by the same amount. So a marker 4 m deep usually means a target about 4 m deep. Each new marker refines the estimate, and the closest marker to the target carries the most weight, because thickness changes have less room to add up.
Thicknesses do change. Compare the interval between two markers with the type well: if it is thicker or thinner, adjust the target prediction in proportion, and say so in the update.
A worked example
The target top is prognosed at 3,000 m TVD, and the plan is to land 1 m inside it. The directional driller is building at 3° per 30 m.
| Marker | Prognosed TVD | Actual TVD | Difference | Predicted target top |
|---|---|---|---|---|
| Marker A | 2,950 m | 2,954 m | 4 m deep | 3,004 m |
| Marker B | 2,980 m | 2,983 m | 3 m deep | 3,003 m |
At Marker B the well is at 80° inclination and 2,983 m TVD. The new landing depth is 3,004 m (1 m into a target now expected at 3,003 m), so the well must gain 21 m of TVD while turning the last 10°.
On a circular build, the depth gained while going from 80° to 90° is R × (sin 90° − sin 80°), where R is the radius of the curve. At 3° per 30 m, R is about 573 m, so the well gains only 8.7 m of TVD and would land about 12 m too high, in the layer above the target.
Two ways to land on depth:
- Build more gently: a build rate of about 1.2° per 30 m gains the 21 m, but stretches the rest of the curve to about 240 m of hole.
- Hold a tangent, then build: hold 80° for about 71 m of hole (gaining about 12 m of TVD), then build at 3° per 30 m to 90° over the last 100 m.
The directional driller picks between them depending on the assembly and dogleg limits. The point of the example is the timing: the problem was visible at Marker B, 21 m above the landing, and still had two workable fixes. Spotted at 5 m above the landing, it would have had none. You can check the geometry with our MD to TVD converter and survey calculator.
Ways to correct the landing
- Change the build rate: slower to land deeper, faster to land shallower, within what the assembly can deliver.
- Add or lengthen a tangent: the common way to land deeper without extra dogleg.
- Land at a different inclination: match the layer's apparent dip, so you do not land flat into a dipping target.
- Land, then adjust: where the target is thick enough, land conservatively high and drift down in the first part of the lateral.
- Plug back and sidetrack: the expensive last resort when the well has gone too deep or out of the target.
Common mistakes
- Waiting for the target top itself instead of acting on the markers above it.
- Ignoring thickness changes between the type well and the drilled well.
- Forgetting sensor-to-bit distance: the bit is deeper than the log shows.
- Landing flat at 90° into a target that dips along the well.
- Late calls that force high build rates and doglegs that hurt the casing run.
- Not telling the driller early that a change is likely.
Landing checklist
- Type well chosen, tops checked, markers above target listed with thickness to the target.
- Landing window and build plan agreed, with the build rate limits written down.
- At every marker: actual vs prognosed TVD, thickness check, new target estimate.
- After every survey: depth to go vs depth the planned curve will gain.
- Changes agreed with the directional driller before the next stand.
- Landing inclination set from the expected apparent dip.
Landing is covered step by step in module 5 of our free geosteering course. Terms used here are defined in the geosteering glossary.
Frequently asked questions
What does landing the curve mean?+
Landing the curve means finishing the build section of a horizontal well so that it enters the target layer at the planned depth and close to horizontal. The point where this happens is the landing point, and the lateral is drilled from there.
Why do markers above the target matter for landing?+
Each marker arriving deeper or shallower than prognosed tells you the target is probably deeper or shallower too. Updating the target depth marker by marker is how the landing point is predicted early enough to change the build.
What is a tangent section in landing?+
A straight, hold-angle stretch inside or at the end of the curve. Holding inclination for a while gains depth without building angle, which is a common way to land deeper than the build alone would.
Should you land at exactly 90 degrees?+
Not necessarily. You land at the inclination that keeps the well parallel to the layer, which is 90 degrees plus or minus the apparent dip. If the layer dips down along the well, the landing inclination is slightly below 90 degrees.
Is a pilot hole needed to land a horizontal well?+
Not always. Where offset wells give a reliable type log, many wells land without a pilot. Where the target depth or thickness is uncertain, a pilot hole or logging the landing itself reduces the risk.